Introduction: In modern society, the level of development of science and technology is very rapid. Many high-tech products that we could not even dream of owning in the past have now been able to be mass-produced and flowed into the hands of ordinary people due to the advancement of scientific and technological research. within the family. Everyone should know about computers, but compared to heavy computers and laptops, tablets seem to be much easier to carry, and it is more convenient to take them with you when traveling. Next, the editor will introduce a flashing tutorial for a tablet computer, Arishun m30.
Notes on flashing:
1. Flashing of AIRISUN and above models can be done while the machine is on or off. brush.
2. All AIRISUN machines must be flashed under the XP system. Win7 will not work unless your computer can successfully install the WIN7 driver.
3. If Ailishun’s machine is turned on and flashed, USB debugging must be turned on, otherwise the flashing tool cannot recognize it; if a friend’s machine is stuck on the boot interface and wants to flash and connect to the computer, but the computer But when it cannot be recognized, it is best to shut down the machine and flash it.
4. When flashing, you need to download the corresponding flashing tool and firmware. Moreover, the flashing tool and firmware are downloaded to your laptop or desktop computer, not to the tablet. The flashing tool needs to be decompressed and installed to flash the phone. Don't worry about the firmware. I would like to remind you that some friends' computers will not recognize the firmware with the suffix img. It doesn't matter. The firmware is just an add-on. Whether your computer recognizes it or not has no impact on flashing.
Tutorial on flashing the phone in the boot state
(1) Download the flash tool (1.7 mass production flash tool) and firmware. Unzip and installOnce you flash the firmware, you don’t need to unzip it.
(2) Run the flash tool (1.7 mass production tool) and add the corresponding firmware. Here we take M30Q as an example. After the addition is successful, the dialog box will show that the firmware has been added successfully.
(3) Connect the tablet with a USB data cable. At this time, the 1 under the flash tool panel will change from gray to pink (indicating that the flash tool has recognized your tablet). If it does not turn pink, If it is not recognized, you need to do the following tests: 1. Connect the tablet with a USB data cable to see if the computer can recognize your hard drive. If it can, it is because USB debugging is not turned on. Just turn on USB debugging at this time. 2. If you use USB to connect to the computer, the hard disk cannot be recognized (that is, the tablet cannot be recognized by the computer). At this time, the tablet driver is not installed or there is a problem with the USB data cable. The test method is as follows: ①. Change a USB data cable and reconnect ② , download 360 Mobile Assistant on your computer, connect the tablet and it will automatically download the driver for the tablet
(4) Click the switch button, then the pink 1 will turn green, and the dialog box will show that the switch is successful.
(5) Click the upgrade button, and wait for the dialog box to remind you that the flashing is completed.
(6) Friendly reminder: After the flashing is completed, the tablet will enter the self-test mode. Everyone You have to wait patiently for a period of time, and flashing the phone usually takes a long time to start up for the first time, so when you turn on the phone, you should pay attention to pressing the power button for a long time. Of course, sometimes flashing the phone once may not solve your problem, so sometimes Need to brush twice.
Tutorial on flashing the phone in shutdown state
(1) Run the flashing tool (1.7 mass production tool) and add the corresponding flashing firmware . Here we take the M30Q as an example
(2) Press and hold the volume button “+” and hold on
(3) Press and hold the volume button “+” without letting go. Connect the tablet to the USB data cable and power charger
(4) After letting go, you will find that the "1" under the flash tool panel turns green directly.
(5) There is no need to switch at this time, just click upgrade and it will be OK.
(6) Friendly reminder: After the flashing is completed, the tablet will enter the self-test mode.Wait patiently for a period of time, and flashing the phone usually takes a long time to start up for the first time, so everyone should pay attention to pressing the power button for a long time when turning on the phone. Of course, sometimes flashing the phone once may not solve your problem, so sometimes it is necessary Brush twice.
Supplementary information about the M30Q shutdown and flashing tutorial:
Some children reported that they had to hold down the volume + button, and then connected the USB data cable and power charger in sequence, and found that the 1 of the flashing tool was not If it turns green, you can try to hold down the volume and hold it and connect the USB data cable and power charger in sequence to see if 1 of the flash tool will turn green. Using these two methods, you can basically shut down the phone and flash it successfully.
OK, the above content is the tablet computer Ericsson m30 introduced by the editor when it is turned on. As well as two different flashing tutorials in the shutdown state, I believe that smart people will be able to quickly familiarize themselves with these two tutorials! Of course, there are also some important precautions during the flashing process, and everyone must read them carefully. Oh, otherwise, an accident may cause the flashing to fail. Everyone must strictly follow the tutorial. If there is anything you don’t understand, it’s best to find a professional to answer it!